Thomas Krenn's guide to OPNsense WireGuard Configuration.OPNsense Forum Wireguard & Mullvad - I'm lost.OPNsense Docs WireGuard MullvadVPN Road Warrior Setup.For more detailed info, see the Port Forwarding Guide on Mullvad's Docs.From here you'll see a list of your public keys, simply press the "Add New" icon under the Ports section of your desired instance, and specify the port your internal service is running on. Log into your Mullvad account, and navigate to /account/ports. If you need to expose a service to the internet from behind Mullvad, then you need to individually assign the ports in your Mullvad account. For more detailed info, see the SOCKS5 Proxy Guide on Mullvad's Docs.Mullvad's WireGuard proxy can be found at 10.64.0.1 port 1080. It's also possible to use the SOCKS5 proxies to multihop, enabling the client to exit from a server that is different from the one you connected to. Optionally, you can use SOCKS5 on client devices or browsers, for additional protection, and improved performance. This is useful to know for if your troubleshooting and unsure why your changes are not taking effect! SOCKS5 Proxy For that, you need to disable, re-enable and save changes in these pages accordingly. Now that everything's up and working, it's worth noting that if you haven't yet configured automated backups, don't forget to export your working config, under System -> Configuration -> Backups :)ĭisabling and re-enabling WireGuard from the General tab does not refresh updated data from the Local or Endpoints tab. Mullvad also has a simple API, that you can call to, and confirm your connection. Here you can also confirm that your IP is not blacklisted, and that there are no DNS or WebRTC leaks. To test your connection to Mullvad, navigate to Under VPN -> WireGuard -> List Configuration, you should now see the connection details Translation / Target: Interface addressĪnd all other fields can be left as defaultįinally, go back to VPN -> WireGuard -> General - and hit Enable WireGuard VPN - Done!.Next, create a new manual rule, with the following details: Under Firewall -> NAT -> Outbound, switch the Rule Generation mode to Hybrid (from automatic). Your Local Instance should now look like this: Under Peers, select the name of your newly created endpoint Navigate back to VPN -> WireGuard -> Local, and click edit for your instance. Your Endpoint should look something like this: Endpoint Port: (multihop port from your chosen Mullvad instance).Public Key: (public key from your chosen Mullvad instance).Under VPN -> WireGuard -> Endpoints, and create a new instance, with the following data: Make note of it's name/ proxy address, public key and port. Navigate to and select a WireGuard server that meets your requirements. Go back to your Local Instance, and under Tunnel Address, add both the IPs returned from the above curl command It's linked to your account, so keep it safe. This will give you an output with 2 IP addresses, like: 00.xx.xxx.xx/xx,fc00:bbbb:bbbb:bb00::0:0x00/128$ SSH into your box, and run the following command, where account number is your 16-digit Mullvad key (without dashes), and public key is from your newly created local instance.Ĭurl -sSL -d account= -data-urlencode pubkey= Once your local config is saved, click edit, and a private and public key should have been automatically generated. Tunnel Address: Leave blank for now, we'll come back to this.If you are using a different VPN, use their DNS here instead) DNS Server: 193.138.218.74 (this is Mullvad's privacy DNS service.Under VPN -> WireGuard -> Local, create a new instance which looks like this: Now you can refresh the page, and go to, go to VPN -> Wireguard Navigate to System -> Firmware -> Plug-ins, and select and install 'os-wireguard'. There wasn't a lot of information online about this, so after I'd (finally) got it working, I wrote this step-by-step guide I am new to OPNsense, and got totally stuck on this.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |